Store

SORT BY

  • LOW - HIGH
  • HIGH - LOW
  • A - Z
  • Z - A
4KW Hi-Frequency Compact Induction Heater w/ Timers 100-250KHz

$2990.00

image

Note: This model only available in 220 volt single phase.

IHG series 100 kHz to 1100 kHz high frequency induction heaters are among the latest products developed by Across International. They can quickly heat most metals that other frequencies can not heat efficiently, like aluminum and metal powders. And uniquely they can heat parts from a distance. These heaters are the ideal tools for fine steel wires (such as those used in dentistry) annealing, small precision shaft quenching, hard alloy saw blade brazing and metal powders melting.

IHG04AC Induction Heater Features

  • Specially designed for welding thin metal parts, blades and melting of small quantity of metallic materials, ultra fast.

  • Ease of use: just plug in the power and connect the water cooling system, our simple instruction allows you to use the heater in 15 minutes.

  • Light weight (only 38 Lb), portable (with built-in handle), instant heat and up to 90% energy savings

  • Precise control with digital output, frequency and current displays.

  • Remote foot switch for safer operation.

  • Dual automatic and manual modes.

  • Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • Frequency is non-adjustable, it depends on the coil design (diameter of turns, numbers of turns, copper tubing diameter and total length).

  • ISO 9001:2008 registered manufacturer.

  • We provide sample testing and custom made coils in our New Jersey facility

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 245V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 245V.

  • Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.

  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Short circuit between work pieces and induction coils

    • Machine malfunctions

    • Induction coils touching each other

    • Input voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any damage caused by misuse.

  • Do not run no-load operation for a long period of time, it might cause damage to the machine.

  • Circulating water must be pure, clean and below 45°C.

  • Machine must be grounded properly all the time during operation.

  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

hidden field
6.6KW Hi-Frequency Compact Induction Heater w/ Timers 100-500KHz

$5790.00

image

Note: This model only available in 220 volt single phase.

IHG series 100 kHz to 1100 kHz high frequency induction heaters are among the latest products developed by Across International. They can quickly heat most metals that other frequencies can not heat efficiently, like aluminum and metal powders. And uniquely they can heat parts from a distance. These heaters are the ideal tools for fine steel wires (such as those used in dentistry) annealing, small precision shaft quenching, hard alloy saw blade brazing and metal powders melting.

IHG06A1 Induction Heater Features

  • Specially designed for welding thin metal parts, blades and melting of small quantity of metallic powder, ultra fast.

  • Ease of use: just plug in the power and connect the cooling system. Our simple instruction allows you to use the heater in 15 minutes.

  • Light weight (only 45 Lb), portable (with built-in handle), instant heat and up to 90% energy savings

  • Precise control with digital output, frequency and current displays.

  • Remote foot switch for a safer operation.

  • Dual automatic and manual modes.

  • Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • Frequency is non-adjustable, it depends on the coil design (diameter of turns, numbers of turns, copper tubing diameter and total length).

  • ISO 9001:2008 registered manufacturer.

  • We provide sample testing and custom made coils in our New Jersey facility

Safety

  • Overvoltage protection: machine shuts down, overvoltage light turns on and buzzer sounds continuously when line voltage exceeds 260V. Alarm shuts off automatically when voltage returns below 260V.

  • Overheat protection: if sensor detects heat sink temperature is over 55°C, machine shuts down, overheat light turns on and buzzer sounds continuously. Decrease water temperature until alarm goes off.

  • Overcurrent/malfunction protections: machine shuts down, indicator light turns on and buzzer sounds continuously in one of these situations:

    • Short circuit exists between work piece and induction coils

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Machine malfunctions

    • Induction coils touching each other

    • Line voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

IMPORTANT

  • Always wear protective gear including goggles when operating the machine. Crucibles must be covered at all times during operation. Across International is not responsible for any injury or damage caused by misuse.

  • Running without a work-piece for extended periods of time may cause damage to the machine.

  • Circulating water must be pure, soft and below 45°C.

  • Machine must be grounded properly at all times.

  • Absolutely no thread tape (or related material) may be used in the installation of induction coils.

hidden field
6.6KW Hi-Frequency Induction Heater w/ Timers 600-1100KHz

$5990.00

image

Note: This model only available in 220 volt single phase.

IHG series 100 kHz to 1100 kHz high frequency induction heaters are among the latest products developed by Across International. They can quickly heat most metals that other frequencies can not heat efficiently, like aluminum and metal powders. And uniquely they can heat parts from a distance. These heaters are the ideal tools for fine steel wires (such as those used in dentistry) annealing, small precision shaft quenching, hard alloy saw blade brazing and metal powders melting.

IHG06A3 Induction Heater Features

  • Separated heater on a cable so it can be used by hand like a wand for added heating flexibility.

  • Specially designed for heating and welding thin metal parts, blades and melting of small quantity of metallic powder, ultra fast.

  • Light weight (only 45 Lb), portable (with built-in handle), instant heat and up to 90% energy savings

  • Ease of use: just plug in the power and connect the water cooling system, our simple instruction allows you to use the heater in 15 minutes.

  • Precise control with digital output, frequency and current displays.

  • Remote foot switch for safer operation.

  • Dual automatic and manual modes.

  • Optional graphite and silica crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • ISO 9001:2008 registered manufacturer.

  • We provide sample testing and custom made coils in our New Jersey facility

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 245V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 245V.

  • Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.

  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Short circuit between work pieces and induction coils

    • Machine malfunctions

    • Induction coils touching each other

    • Input voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

CAUTION

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any damage caused by misuse.

  • Do not run no-load operation for a long period of time, it might cause damage to the machine.

  • Circulating water must be pure, clean and below 45°C.

  • Machine must be grounded properly all the time during operation.

  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

hidden field
10KW Hi-Frequency Compact Induction Heater w/ Timers 100-500KHz

$7990.00

image

Note: This model only available in 220 volt single phase.

IHG series 100 kHz to 1100 kHz high frequency induction heaters are among the latest products developed by Across International. They can quickly heat most metals that other frequencies can not heat efficiently, like aluminum and metal powders. And uniquely they can heat parts from a distance. These heaters are the ideal tools for fine steel wires (such as those used in dentistry) annealing, small precision shaft quenching, hard alloy saw blade brazing and metal powders melting.

Main Features

  • Specially designed for heating and welding thin metal parts, blades and melting of small quantity of metallic materials, ultra fast.

  • Ease of use: just plug in the power and connect the water cooling system, our simple instruction allows you to use the heater in 15 minutes.

  • Precise control with digital output, frequency and current displays.

  • Remote foot switch for safer operation.

  • Dual automatic and manual modes.

  • Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • Frequency is non-adjustable, it depends on the coil design (diameter of turns, numbers of turns, copper tubing diameter and total length).

  • ISO 9001:2008 registered manufacturer.

  • We provide sample testing and custom made coils in our New Jersey facility

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 245V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 245V.

  • Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.

  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Short circuit between work pieces and induction coils

    • Machine malfunctions

    • Induction coils touching each other

    • Input voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any damage caused by misuse.

  • Do not run no-load operation for a long period of time, it might cause damage to the machine.

  • Circulating water must be pure, clean and below 45°C.

  • Machine must be grounded properly all the time during operation.
  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.
hidden field
20KW Hi-Frequency Split Induction Heater w/ Timers 50-250KHz

$11990.00

image

Note: This model is 460-480 volt three phase.

IHG series 100 kHz to 1100 kHz high frequency induction heaters are among the latest products developed by Across International. They can quickly heat most metals that other frequencies can not heat efficiently, like aluminum and metal powders. And uniquely they can heat parts from a distance. These heaters are the ideal tools for fine steel wires (such as those used in dentistry) annealing, small precision shaft quenching, hard alloy saw blade brazing and metal powders melting.

Main Features

  • Specially designed for heating and welding thin metal parts, blades and melting of small quantity of metallic materials, ultra fast.

  • Ease of use: just plug in the power and connect the water cooling system, our simple instruction allows you to use the heater in 15 minutes.

  • Precise control with digital output, frequency and current displays.

  • Remote foot switch for safer operation.

  • Dual automatic and manual modes.

  • Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • Frequency is non-adjustable, it depends on the coil design (diameter of turns, numbers of turns, copper tubing diameter and total length).

  • ISO 9001:2008 registered manufacturer.

  • We provide sample testing and custom made coils in our New Jersey facility

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 495V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 495V.

  • Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.

  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Short circuit between work pieces and induction coils

    • Machine malfunctions

    • Induction coils touching each other

    • Input voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any damage caused by misuse.

  • Do not run no-load operation for a long period of time, it might cause damage to the machine.

  • Circulating water must be pure, clean and below 45°C.

  • Machine must be grounded properly all the time during operation.

  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

hidden field
40KW Hi-Frequency Split Induction Heater w/ Timers 50-200KHz

$21990.00

image

Note: This model only available in 460-480 volt three-phase.

IHG series 100 kHz to 1100 kHz high frequency induction heaters are among the latest products developed by Across International. They can quickly heat most metals that other frequencies can not heat efficiently, like aluminum and metal powders. And uniquely they can heat parts from a distance. These heaters are the ideal tools for fine steel wires (such as those used in dentistry) annealing, small precision shaft quenching, hard alloy saw blade brazing and metal powders melting.

Main Features

  • Specially designed for heating and welding thin metal parts, blades and melting of small quantity of metallic materials, ultra fast.

  • Ease of use: just plug in the power and connect the water cooling system, our simple instruction allows you to use the heater in 15 minutes.

  • Precise control with digital output, frequency and current displays.

  • Remote foot switch for safer operation.

  • Dual automatic and manual modes.

  • Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • ISO 9001:2008 registered manufacturer.

  • We provide sample testing and custom made coils in our New Jersey facility

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 495V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 495V.

  • Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.

  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Short circuit between work pieces and induction coils

    • Machine malfunctions

    • Induction coils touching each other

    • Input voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any damage caused by misuse.

  • Do not run no-load operation for a long period of time, it might cause damage to the machine.

  • Circulating water must be pure, clean and below 45°C.

  • Machine must be grounded properly all the time during operation.

  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

hidden field
30KW Hi-Frequency Split Induction Heater w/ Timers 50-200KHz

$16990.00

image

Note: This model only available in 460-480 volt three-phase.

IHG series 100 kHz to 1100 kHz high frequency induction heaters are among the latest products developed by Across International. They can quickly heat most metals that other frequencies can not heat efficiently, like aluminum and metal powders. And uniquely they can heat parts from a distance. These heaters are the ideal tools for fine steel wires (such as those used in dentistry) annealing, small precision shaft quenching, hard alloy saw blade brazing and metal powders melting.

Main Features

  • Specially designed for heating and welding thin metal parts, blades and melting of small quantity of metallic materials, ultra fast.

  • Ease of use: just plug in the power and connect the water cooling system, our simple instruction allows you to use the heater in 15 minutes.

  • Precise control with digital output, frequency and current displays.

  • Remote foot switch for safer operation.

  • Dual automatic and manual modes.

  • Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • ISO 9001:2008 registered manufacturer.

  • We provide sample testing and custom made coils in our New Jersey facility

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 495V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 495V.

  • Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.

  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Short circuit between work pieces and induction coils

    • Machine malfunctions

    • Induction coils touching each other

    • Input voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any damage caused by misuse.

  • Do not run no-load operation for a long period of time, it might cause damage to the machine.

  • Circulating water must be pure, clean and below 45°C.

  • Machine must be grounded properly all the time during operation.

  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

hidden field
60KW Hi-Frequency Split Induction Heater w/ Timers 30-150KHz

$26990.00

image

Note: This model only available in 460-480 volt three-phase.

IHG series 100 kHz to 1100 kHz high frequency induction heaters are among the latest products developed by Across International. They can quickly heat most metals that other frequencies can not heat efficiently, like aluminum and metal powders. And uniquely they can heat parts from a distance. These heaters are the ideal tools for fine steel wires (such as those used in dentistry) annealing, small precision shaft quenching, hard alloy saw blade brazing and metal powders melting.

Main Features

  • Specially designed for heating and welding thin metal parts, blades and melting of small quantity of metallic materials, ultra fast.

  • Ease of use: just plug in the power and connect the water cooling system, our simple instruction allows you to use the heater in 15 minutes.

  • Precise control with digital output, frequency and current displays.

  • Remote foot switch for safer operation.

  • Dual automatic and manual modes.

  • Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • ISO 9001:2008 registered manufacturer.

  • We provide sample testing and custom made coils in our New Jersey facility

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 495V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 495V.

  • Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.

  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Short circuit between work pieces and induction coils

    • Machine malfunctions

    • Induction coils touching each other

    • Input voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any damage caused by misuse.

  • Do not run no-load operation for a long period of time, it might cause damage to the machine.

  • Circulating water must be pure, clean and below 45°C.

  • Machine must be grounded properly all the time during operation.

  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

hidden field
25KW Low-Frequency Dual-Station Induction Heater 1-20KHz

$8990.00

image

Note: This model only available in 460-480 volt three-phase.

Across International's IHL series 1 kHz to 20 kHz low frequency induction heaters are good for a wide range of applications including deep heat penetration for full hardening processes, steel rod forging, tempering of pressing dies, pre-heating for welding, and melting of metal batches over 4 lbs. They are not limited to ferromagnetic materials, so nonferrous metals can also be used effectively.

There are three major components to the system: the power supply, the compensating capacitor/transformer and the induction coil/smelting crucible. Our heaters automatically adjust to the best resonant frequency in order to achieve the most efficient overall heating results based on our customer's requirements which include heat penetration, heating efficiency, operating noise and electromagnetic homogeneity. Two of our most popular low frequency machines are the Melting Furnaces with Tilt-Pour Melter and Auto-feeding Rod Heating Furnaces for Forging.

Main Features

  • Dual-station with connection cables and hose let you separate the heater and controller up to seven feet, allow you to stay away from high temperature, dirty and corrosive environment and for a safer operation, or if you need to move the heater to your work pieces constantly during operation.

  • Ease of use: just plug in the power and connect the water cooling system. Our simple instruction allows you to use the heater in 15 minutes.

  • Precise control with digital output, frequency and current displays.

  • Light weight, portable, instant heat and up to 90% energy savings.

  • Remote foot switch for safer operation.

  • Dual automatic and manual modes.

  • Optional graphite, MgO and SiO2 crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)

  • Custom coil design available (fixed coil or coil on a cable so it can be used like a wand)

  • ISO 9001:2008 registered manufacturer.

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 495V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 495V.

  • Overheat protection: if sensor detects heat radiator temperature is over 55°C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.

  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:

    • One of the machine parts becomes overheated

    • Interfering signal detected

    • Short circuit between work pieces and induction coils

    • Machine malfunctions

    • Induction coils touching each other

    • Input voltage is too low

  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any injury or damage caused by misuse.

  • Do not run no-load operation for a long period of time, it might cause damage to the machine.

  • Circulating water must be pure, clean and below 45°C.

  • Machine must be grounded properly all the time during operation.

  • Do NOT use single-turn coil if coil diameter is smaller than 4 inches, it will cause high frequency damage to the machine.

  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

hidden field